RELATEED usb data recovery question
Do need help recover lost file on the usb drive
close usb
Linq urc 8900 manual, Télécommande Universelle - Energy Sis
  • Author:urecovery
  • Publish Time:2018-09-30 09:10

1How to install the battery
Alkaline batteries are recommended. The number of batteries
On the back of the cover.
1. Remove the battery cover on the back of the URC.
2. Observe the polarity of the battery and the "+/-" mark inside the battery
car.
3. Insert the battery.
4. Push the battery cover back into place.
Not enough power
If the indicator flashes twice slowly after any command is called, it indicates that the indicator is blinking
Indicates that the battery is low. You must replace the battery
Make sure it works.
2How to set up URC
Input device code
You can set the URC by entering a description with the code below.
1. Please refer to the device code list for 4-bit device code
Corresponds to the brand of your A/V device. If there are more
A device code is listed under your brand. Try the first code.
2. Press the desired device mode button (for example).TV
3. Simultaneously press "CH +" and "VOL-" 2 on the URC
The number of seconds until the indicator lights up.
4. Use the numeric keys to enter your 4-digit device code, indicator light
I should go out right away.
Turn on the device (such as a TV) and try the function keys on the URC. If your device
(eg TV) correctly responds to the function you called, you have entered
The correct device code. Otherwise, please repeat the above setup instructions
Rest the available device code until your device (eg TV) responds to your call
Features, most keys work fine.
* Just repeat the above steps to enter the device code for you
Video recorder, SAT, DVD or CTV. (Remember to press the correct device mode button
In step 2 above)
Note:
- DVD, CTV and other device code can be entered into any device mode
In addition to the "television" and "recorder" modes. Just press the device mode button
And enter the 4-digit device code for DVD, CTV and other devices.
If the indicator flashes twice in step 4, the device code is incorrect.
enter. You will need to repeat steps 2 through 4 again.
Suggest:
- If you can't find a device specification for your device, see 2 How to operate
Set URC - search through the library.
- It is recommended that you write down your device code in the space provided.
On the back label after setting the URC correctly for future reference.
1
Search through the library
English
If you can't identify the correct device code for your device from your device
Code list, you can search the code through the library: -
1. Turn on the device manually (such as a TV).
2. Press the desired device mode button (for example).TV
3. Simultaneously press "CH +" and "VOL-" 2 on the URC
The number of seconds until the indicator lights up.
4. Enter the appropriate Magic Search code from the table below. index
I should go out right away.
Device Type: TV VCR SAT CTV DVD
Magic search code: 0001 0002 0003 0004 0005
(eg by device mode button,
Then press "television
Enter the TV magic search code 0001.)
CH + "and" VOL-", and
5. Press the same desired device mode button again, as shown in step 2 above. (for example) TV
6. Press and hold "CH +" and "VOL-" simultaneously for 2 seconds until
The indicator lights up and your URC is ready to start searching.
7. Align the URC with your device (eg TV), press the "" key repeatedly, slowly
Be patient until the device is turned off.
Press device mode immediately after turning off the device
Key (for example
)TV
Lock the code and the indicator should go out.
* Just repeat the above setup steps to search for device code
Your VCR, SAT, DVD or CTV. (Remember to press the correct device mode
The key and correct Magic Search code in steps 2-5 above)
Important:
- If your device's power on/off function does not have infrared control - you
Need to start searching according to steps 2 to 6 above: -
• Press "" and another important function key alternately until your
The device responds to the expected function, in the same device mode
Key (for example
) lock the TV
Code.
For example, alternately press "" and "1", or;
Press "" and "" alternately.
note:
- Search DVD, CTV and other device code and lock it
The device mode is in addition to the "TV" and "VCR" modes. Just press the appropriate one.
In step 2 and 5 the device mode key and enter the appropriate magic
Search codes for your DVD, CTV and other devices.
- Each time you press "", the URC will jump to the next code and
Send a power signal to try to shut down your device.
If you fail to stop pressing "" when the device is running
Close and immediately turn on your device again. Before the indicator
Turn off, press "" on the URC to skip backwards. Repeat step 7
Above and lock the code.
- If the indicator flashes twice after pressing the "" button, it means that you are
Already the last code in the library. Press "CH +" and "VOL-" to continue
URC and carefully repeat the above procedure to search again.
2
3 operation URC
General surgery
English
Once the URC is set up for your A/V device, it's like your original device
remote control. Operate, just aim at it